[May 04, 2023] Latest NACE-CIP2-001 PDF Dumps & Real Tests Free Updated Today
NACE-CIP2-001 Dumps With 100% Verified Q&As - Pass Guarantee or Full Refund
NEW QUESTION 36
Corrosion is the reverse process of
- A. galvanic deterioration.
- B. flaking.
- C. steel manufacturing.
- D. hot dipping.
Answer: C
NEW QUESTION 37
Thermal Spray coatings provide:
- A. Inhibitive protection
- B. Barrier protection
- C. Sacrificial protection
- D. Thermal protection
Answer: C
NEW QUESTION 38
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Gathering
- B. Distribution
- C. Midstream
- D. Transmission
Answer: B
NEW QUESTION 39
Application of Thermal Spray Coatings requires:
- A. The same skills as liquid coatings
- B. The same skills as welding
- C. Specialized skills supported by training and experience
- D. No particular skills
Answer: C
NEW QUESTION 40
Pre-cleaning of work pieces will NOT remove
- A. mill scale.
- B. oil or grease.
- C. snow, ice or water.
- D. dirt.
Answer: A
NEW QUESTION 41
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. Consensus
- B. De facto
- C. Mandatory
- D. Voluntary
Answer: D
NEW QUESTION 42
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Safety
- B. Cost
- C. Iron content
- D. Appearance
Answer: C
NEW QUESTION 43
It is always possible to see moisture on a steel substrate:
- A. False
- B. True
Answer: A
NEW QUESTION 44
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It contains biocide
- C. It doesn't contain biocide
- D. It will result in a very slippery surface
Answer: B
NEW QUESTION 45
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. type of dehumidification equipment (refrigerant or desiccant).
- B. coating type.
- C. manufacturer of the equipment.
- D. time of the year (winter/summer).
Answer: B
NEW QUESTION 46
Ideally, documentation requirements should be defined:
- A. By the contractor
- B. In the specification
- C. At the pre-job conference
- D. By the inspector
Answer: B
NEW QUESTION 47
Inspection and Test plans are developed by referencing:
- A. The Specification, SDS, relevant Standards and Codes
- B. The Specification, Application Guidelines, 'Relevant Standards and Codes
- C. The Specification, Safety Manual, Relevant Standards and Codes
- D. The Specification, TDS, relevant Standards and Codes
Answer: D
NEW QUESTION 48
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Fusion Bonded Epoxy
- B. 2-Layer Polyethylene (PE)
- C. 3-Layer Polyethylene (PE)
- D. Coal Tar Enamel
Answer: C
NEW QUESTION 49
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. No difference from any other coating
- B. A very low reading
- C. Cold flow or creep
- D. A very high reading
Answer: C
NEW QUESTION 50
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method A - Cross Hatch
- B. Method B - Cross Hatch
- C. Method B - X cut
- D. Method A - X Cut
Answer: D
NEW QUESTION 51
......
2023 Valid NACE-CIP2-001 test answers & NACE Exam PDF: https://testking.guidetorrent.com/NACE-CIP2-001-dumps-questions.html